Exhaust fans
Exhaust fans with stainless steel blade (Galvanized frame) - EX-50-
Associated documents
Assembly manual (PDF)
(Request password)
Exhaust fans with stainless steel blade (Galvanized frame) - EX-50-
The entire range of the EX fans are mainly based on its long endurance, low maintenance and excellent air flow/power consumption.
- Fan structure made of galvanized
- Sheets made of steel with a reinforced centrifugal opening system
- Central pulley and propeller support including a high quality water tight greased bearing for life.
- Motor with an IP 55 protection and insulating coil degree type F.
- Fan venturi made of plastic material with UV protection.
- Front grid according to regulation.
- Locking shutter with a specific design in order to avoid the air inlet and light entrance.
*Possibility to supply with a motor IE
MODELS
Ref | Subst | Description |
EX1NX-50T | 20030 | Three-phase exhaust fan with stainless steel blades of 1 HP |
EX15NX-50T | 20040 | Three-phase exhaust fan with stainless steel blades of 1´5 HP |
EX1NX-50T-IE2 | 20030-IE2 | Three-phase exhaust fan with stainless steel blades of 1 HP. IE2 |
EX15NX-50T-IE2 | 20040-IE2 | Three-phase exhaust fan with stainless steel blades of 1´5 HP. IE2 |
TECHNICAL DATA
MODEL | AIR FLOW | FAN | MOTORIII | NIVEL SON. | APROX WEIGH |
EX 50¨-1 | 38.600 m3/h / 22.700 CFM | Ø 1.270 | 1 CV / 0.76 Kw / 230 - 400 V (Tensión) | 67 Dba | 85 |
EX 50¨-1,5 | 41.900 m3/h / 24.600 CFM | Ø 1.270 | 1.5 CV / 1.1 Kw / 230 - 400 V (Tensión) | 69 Dba | 85 |
DIMENSIONS
A | B | C | |
EX50¨-1 | 1.380 | 1.380 | 450 |
EX50¨-1,5 | 1.380 | 1.380 | 450 |
*Measure (mm)
Exhaust fans with galvanized blades (Galvanized frame) - EX-50-
Associated documents
Assembly manual (PDF)
(Request password)
Exhaust fans with galvanized blades (Galvanized frame) - EX-50-
The entire range of the EX fans are mainly based on its long endurance, low maintenance and excellent air flow/power consumption.
- Fan structure made of galvanized.
- Sheets made of steel with a reinforced centrifugal opening system.
- Central pulley and propeller support including a high quality water tight greased bearing for life.
- Motor with an IP 55 protection and insulating coil degree type F.
- Fan venturi made of plastic material with UV protection.
- Front grid according to regulation.
- Locking shutter with a specific design in order to avoid the air inlet and light entrance.
*Possibility to supply with a motor IE2
MODELS
Ref | Subst | Description |
EX1GV-50T | 21030 | Three - phase exhaust fan with stainless steel blades of 1 HP |
EX15GV-50T | 21040 | Three - phase exhaust fan with stainless steel blades of 1´5 HP |
EX1GV-50T-IE2 | 21030-IE2 | Three-phase exhaust fan with galvanized steel blades of 1 HP. IE2 |
EX15GV-50T-IE2 | 21040-IE2 | Three-phase exhaust fan with galvanized steel blades of 1´5 HP. IE2 |
TECHNICAL DATA
MODELO | AIR FLOW | FAN | MOTORIII | NIVEL SON. | APROX WEIGHT |
EX 50¨-1 | 38.600 m3/h / 22.700 CFM | Ø 1.270 | 1 CV / 0.76 Kw / 230 - 400 V (Tensión) | 67 Dba | 85 |
EX 50¨-1,5 | 41.900 m3/h / 24.600 CFM | Ø 1.270 | 1.5 CV / 1.1 Kw / 230 - 400 V (Tensión) | 69 Dba | 85 |
DIMENSIONS
A | B | C | |
EX50¨-1 | 1.380 | 1.380 | 450 |
EX50¨-1,5 | 1.380 | 1.380 | 450 |
*Measure (mm)
- The new aerodynamic design of the blades improves the efficiency of the whole set by obtaining a higher value of the flow ratio (m3/h) per electric consumption unit in watts. The aerodynamic design of the propellers by means of the computer programs in cooperation with the most prestigious test beds, enable us to distribute the pressure on the hydrodynamic profiles along the blade, and so achieve higher efficiency.
- The new shutter improves the aerodynamic set coefficient and allows to better close in order to avoid the light and air inlet inside the facilities. The new design of the closing shutter design guarantees a higher opacity in order to prevent the light from getting inside. It also enables a higher water tightness degree for a perfect insulation when the fan is in pause mode.
- The centrifugal system is made of black acetyl resin with UV protection.
- Sliding motor especially designed to reduce the stress of the motor bearings and improve the new highly efficient electric motor performance; this prolongs the useful life of the equipment along with a higher power efficiency.
- The special support made of plastic fixes the mesh and eliminates any vibration.
Exhaust fans with stainless steel blade EX50
Associated documents
Ferrule assembly
(Request password)Structure assembly
(Request password)Assembly of the motor on the structure
(Request password)Assembly of the bushing, pulley, bar and drive mechanism
(Request password)Assembly of the propeller, centrifuge and grommet
(Request password)Assembly of the protection an mesh
(Request password)Shutter assembly
(Request password)Assembly lateral lid
(Request password)Placing of the stickers
(Request password)Assembly manual (PDF)
(Request password)
Exhaust fans withstainless steel blade EX50
The entire range of the EX fans are mainly based on its long endurance, low maintenance and excellent air flow/power consumption.The design system of the R + D department as well as the quality of the materials used, guarantee its total reliability and resistance thanks to more than 25 years of experience in the sector.
- Fan structure made of stainless steel.
- Sheets made of steel with a reinforced centrifugal opening system
- Central pulley and propeller support including a high quality water tight greased bearing for life.
- Motor with an IP 55 protection and insulating coil degree type F.
- Fan venturi made of plastic material with UV protection.
- Front grid according to regulation.
- Locking shutter with a specific design in order to avoid the air inlet and light entrance.
*Possibility to supply with a motor IE2
MODELS
Ref | Subst | Description |
EX1-50T-INOX | 20031 | Three - phase exhaust fan Ex50” with stainless steel blades of 1 HP |
EX15-50T-INOX | 20041 | Three - phase exhaust fan Ex50” with stainless steel blades of 1´5 HP |
EX1-50T-IE2-INOX | 20031-IE2 | Three-phase exhaust fan EX 50” totally in stainless steel of 1 HP. IE2 motor |
EX15-50T-IE2-INOX | 20041-IE2 | Three-phase exhaust fan EX 50” totally in stainless steel of 1 HP. IE2 motor |
TECHNICAL DATA
MODEL | AIR FLOW | FAN | MOTORIII | NIVEL SON. | APROX WEIGHT |
EX 50¨-1 | 38.600 m3/h / 22.700 CFM | Ø 1.270 | 1 CV / 0.76 Kw / 230 - 400 V (Tensión) | 67 Dba | 85 |
EX 50¨-1,5 | 41.900 m3/h / 24.600 CFM | Ø 1.270 | 1.5 CV / 1.1 Kw / 230 - 400 V (Tensión) | 69 Dba | 85 |
DIMENSIONS
A | B | C | |
EX50¨-1 | 1.380 | 1.380 | 450 |
EX50¨-1,5 | 1.380 | 1.380 | 450 |
*Measure (mm)
- The new aerodynamic design of the blades improves the efficiency of the whole set by obtaining a higher value of the flow ratio (m3/h) per electric consumption unit in watts. The aerodynamic design of the propellers by means of the computer programs in cooperation with the most prestigious test beds, enable us to distribute the pressure on the hydrodynamic profiles along the blade, and so achieve higher efficiency.
- The new shutter improves the aerodynamic set coefficient and allows to better close in order to avoid the light and air inlet inside the facilities. The new design of the closing shutter design guarantees a higher opacity in order to prevent the light from getting inside. It also enables a higher water tightness degree for a perfect insulation when the fan is in pause mode.
- The centrifugal system is made of black acetyl resin with UV protection.
- Sliding motor especially designed to reduce the stress of the motor bearings and improve the new highly efficient electric motor performance; this prolongs the useful life of the equipment along with a higher power efficiency.
- The special support made of plastic fixes the mesh and eliminates any vibration.
Ventiladores de gran caudal from EXAFAN S.A. on Vimeo.
Exhaust fans with stainless steel blade EX36
Associated documents
Assembly manual (PDF)
(Request password)
Exhaust fans with stainless steel blade EX36
The entire range of the EX fans are mainly based on its long endurance, low maintenance and excellent air flow/power consumption.The design system of the R + D department as well as the quality of the materials used, guarantee its total reliability and resistance thanks to more than 25 years of experience in the sector.
- Fan structure made of stainless steel.
- Sheets made of steel with a reinforced centrifugal opening system
- Central pulley and propeller support including a high quality water tight greased bearing for life.
- Motor with an IP 55 protection and insulating coil degree type F.
- Fan venturi made of plastic material with UV protection.
- Front grid according to regulation.
- Locking shutter with a specific design in order to avoid the air inlet and light entrance.
MODELS
Ref | Subst | Description |
EX05NX-50T-INOX | 20011 | Three - phase exhaust fan EX36 with stainless steel blades of 0´5 HP |
EX075NX-50T-INOX | 20021 | Three - phase exhaust fan EX36 with stainless steel blades of 0´75 HP |
TECHNICAL DATA
MODEL | AIR FLOW | FAN | MOTORIII | NIVEL SON. | APROX WEIGHT |
EX 36¨-0.5 | 19.100 m3/h / 11.240 CFM | Ø 915 | 0.5 CV / 0.38 Kw / 230 - 400 V (Tensión) | 62 Dba | 65 |
EX 36¨-0.75 | 21.600m3/h / 12.960CFM | Ø 915 | 0.75 CV / 0.55 Kw / 230 - 400 V (Tensión) | 62 Dba | 65 |
DIMENSIONS
A | B | C | |
EX36¨-0.5 | 1.090 | 1.090 | 450 |
EX36¨-0,75 | 1.090 | 1.090 | 450 |
*Measure (mm
- The new aerodynamic design of the blades improves the efficiency of the whole set by obtaining a higher value of the flow ratio (m3/h) per electric consumption unit in watts. The aerodynamic design of the propellers by means of the computer programs in cooperation with the most prestigious test beds, enable us to distribute the pressure on the hydrodynamic profiles along the blade, and so achieve higher efficiency.
- The new shutter improves the aerodynamic set coefficient and allows to better close in order to avoid the light and air inlet inside the facilities. The new design of the closing shutter design guarantees a higher opacity in order to prevent the light from getting inside. It also enables a higher water tightness degree for a perfect insulation when the fan is in pause mode.
- The centrifugal system is made of black acetyl resin with UV protection.
- Sliding motor especially designed to reduce the stress of the motor bearings and improve the new highly efficient electric motor performance; this prolongs the useful life of the equipment along with a higher power efficiency.
- The special support made of plastic fixes the mesh and eliminates any vibration.
Exhaust fans with stainless steel blade (Galvanized frame) - EX36 -
Associated documents
Assembly manual (PDF)
(Request password)
Exhaust fans with stainless steel blade (Galvanized frame) - EX36 -
The entire range of the EX fans are mainly based on its long endurance, low maintenance and excellent air flow/power consumption.
- Fan structure made of galvanized
- Sheets made of steel with a reinforced centrifugal opening system
- Central pulley and propeller support including a high quality water tight greased bearing for life.
- Motor with an IP 55 protection and insulating coil degree type F.
- Fan venturi made of plastic material with UV protection.
- Front grid according to regulation.
- Locking shutter with a specific design in order to avoid the air inlet and light entrance.
*Possibility to supply with a motor IE
MODELS
Ref | Subst | Description |
EX05NX-50T | 20010 | Three - phase exhaust fan Ex36” with stainless steel blades of 0´5 HP |
EX075NX-50T | 20020 | Three - phase exhaust fan Ex36” with stainless steel blades of 0´75 HP |
TECHNICAL DATA
MODELS | AIR FLOW | FAN | MOTORIII | NIVEL SON. | APROX WEIGH |
EX 36¨-0.5 | 19.100 m3/h / 11.240 CFM | Ø 915 | 0.5 CV / 0.38 Kw / 230 - 400 V (Tensión) | 62 Dba | 65 |
EX 36¨-0.75 | 21.600m3/h / 12.960CFM | Ø 915 | 0.75 CV / 0.55 Kw / 230 - 400 V (Tensión) | 62 Dba | 65 |
DIMENSIONS
A | B | C | |
EX36¨-0.5 | 1.090 | 1.090 | 450 |
EX36¨-0,75 | 1.090 | 1.090 | 450 |
*Measure (mm)
Exhaust fans with galvanized blades (Galvanized frame) - EX36 -
Associated documents
Assembly manual (PDF)
(Request password)
- Exhaust fans with galvanized blades (Galvanized frame) - EX36 -
he entire range of the EX fans are mainly based on its long endurance, low maintenance and excellent air flow/power consumption.
- Fan structure made of galvanized.
- Sheets made of steel with a reinforced centrifugal opening system.
- Central pulley and propeller support including a high quality water tight greased bearing for life.
- Motor with an IP 55 protection and insulating coil degree type F.
- Fan venturi made of plastic material with UV protection.
- Front grid according to regulation.
- Locking shutter with a specific design in order to avoid the air inlet and light entrance.
*Possibility to supply with a motor IE2
MODELS
Ref | Subst | Description |
EX05GV-50T | 21010 | Three-phase exhaust fan Ex36” with galvanized steel blades of 0´5 HP |
EX075GV-50T | 21020 | Three-phase exhaust fan Ex36” with galvanized steel blades of 0´75 C.V |
TECHNICAL DATA
MODELO | AIR FLOW | FAN | MOTORIII | NIVEL SON. | APROX WEIGHT |
EX 36¨-0.5 | 19.100 m3/h / 11.240 CFM | Ø 915 | 0.5 CV / 0.38 Kw / 230 - 400 V (Tensión) | 62 Dba | 65 |
EX 36¨-0.75 | 21.600m3/h / 12.960CFM | Ø 915 | 0.75 CV / 0.55 Kw / 230 - 400 V (Tensión) | 62 Dba | 65 |
DIMENSIONS
A | B | C | |
EX36¨-0.5 | 1.090 | 1.090 | 450 |
EX36¨-0,75 | 1.090 | 1.090 | 450 |
*Measure (mm)